Configure the BlueDiamond reader with OSDP using configuration cards. Begin using the cards within 60 seconds of the reader powering up, or within 60 seconds of presenting the BDC-UNLOCK configuration card. Each subsequent configuration card presented extends the allowable configuration time window by another 60 seconds. If 60 seconds passes, present the BDC-UNLOCK configuration card again.

BDC-UNLOCK

Use the BDC-UNLOCK configuration card to switch the BlueDiamond reader into configuration mode for 60 seconds. The reader confirms the BDC-UNLOCK card with a multi-tone sound. Present any BlueDiamond configuration card to the reader after using the BDC-UNLOCK card.

BDC-CSN

Use the BDC-CSN configuration card to set the BlueDiamond reader configuration:

  • Wiegand output
  • Tamper enabled
  • Tone-on keypad
  • Tone-on card
  • Wiegand LED and buzzer behavior

In this configuration, the BlueDiamond reader accepts the following credentials:

Credential

Output

BlueDiamond Mobile

Encoded Wiegand payload

MIFARE Classic

32 bit CSN

MIFARE DESFIRE

56 bit CSN

HID iCLASS

64 bit CSN converted to 5502 Wiegand format

HID Prox

Encoded Wiegand payload

GE ProxLite

4002 Wiegand format

AWID Prox

Encoded Wiegand payload

BDC-DESFIRE

Use the BDC-DESFIRE configuration card to set the following BlueDiamond reader configurations:

  • Wiegand output
  • Tamper enabled
  • Tone-on keypad
  • Tone-on card
  • Wiegand LED and buzzer behavior

Note

This card is only required when using older DEV17 readers. DEV30 and greater have this as the default configuration.

In this configuration, the BlueDiamond reader accepts the following credentials:

Credential

Output

BlueDiamond Mobile

Encoded Wiegand payload

BlueDiamond DESFire

Encoded Wiegand payload

HID iCLASS

Encoded Wiegand payload

HID Prox

Encoded Wiegand payload

GE ProxLite

4002 Wiegand format

AWID Prox

Encoded Wiegand payload

Note

The BlueDiamond reader ships with this default configuration.

BDC-UID

Use the BDC-UID configuration card to change the smart card serial number configuration in the reader output. Each time you present this card, the reader indicates the current configuration using a number of short tones.

  • 1 beep - Pass-through (Big Endian)
  • 2 beeps - 32 Bit (Big Endian)
  • 3 beeps - Pass-through (Little Endian)
  • 4 beeps - 32 Bit (Little Endian)
  • 5 beeps - MIFARE 4byte/DESFire 7byte 4002

1 Beep = Pass-through (Big Endian)

Credential

Output

MIFARE Classic

32 bit CSN Big Endian

MIFARE DESFIRE

56 bit CSN Big Endian

HID iCLASS

iCLASS CSN converted to 5502 Wiegand

2 Beeps = 32 bit (Big Endian)

Credential

Output

MIFARE Classic

32 bit CSN Big Endian

MIFARE DESFIRE

DESFire CSN truncated to 32 bit Big Endian

HID iCLASS

iCLASS CSN Truncated to 32 bit Big Endian

3 Beeps = Pass-through (Little Endian)

Credential

Output

MIFARE Classic

32 bit CSN Little Endian

MIFARE DESFIRE

56 bit CSN Little Endian

HID iCLASS

iCLASS CSN converted to 5502 Wiegand

4 Beeps = 32 bit (Little Endian)

Credential

Output

MIFARE Classic

32 bit CSN Little Endian

MIFARE DESFIRE

DESFire CSN truncated to 32 bit Little Endian

HID iCLASS

iCLASS CSN truncated to 32 bit Little Endian

5 Beeps = MIFARE 4byte/DESFire 7byte - 4002

Credential

Output

MIFARE Classic

32 bit CSN converted 4002 Wiegand

MIFARE DESFIRE

DESFire CSN converted to 4002 Wiegand

HID iCLASS

iCLASS CSN converted to 5502 Wiegand

BDC-RADIO

Use the BDC-RADIO configuration card to configure the BlueDiamond reader to ignore High Frequency (smart cards) or Low Frequency (Prox. cards) cards. Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 1 beep - 13.56MHz and 125KHz are active
  • 2 beeps - Only 13.56MHz is active
  • 3 beeps - Only 125KHz is active
  • 4 beeps - Neither radio is active

Note

BlueDiamond BTLE radio is not controlled by this card - refer to BDC-BLUETOOTH.

BDC-TONE

Use the BDC-TONE configuration card to set the reader default tone behavior. Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 1 beep - reader does not beep when a credential is presented
  • 2 beeps - reader beeps when a credential is presented

This configuration is applicable to the readers communicating over Wiegand.

BDC-LED

Use the BDC-LED configuration card to set the color and pulsing activity for the idle reader LED behavior. Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 1 beep - Solid blue
  • 2 beeps - Pulsing blue
  • 3 beeps - Solid red
  • 4 beeps - Pulsing red

This configuration is applicable to the readers communicating over Wiegand. The LED idle behavior happens during off periods when the LED is not controlled by RED or GREEN reader pins. For instance, when the LED is blinking RED/OFF/RED/OFF, you can change it to RED/BLUE/RED/BLUE.

BDC-OSDPSEC

Use the BDC-OSDPSEC card to reset OSDP Secure Channel Key and prepare for pairing with the OSDP panel in Secure Channel Mode. Use this card to take the reader out of OSDP Secure Channel mode and into standard OSDP while preserving the rest of the reader configuration.

BDC-OSDPADD

Use the BDC-OSDPADD card to set the OSDP address and configure communications with OSDP Panel. Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 1 beep - OSDP Address 0
  • 2 beeps - OSDP Address 1
  • 3 beeps - OSDP Address 2
  • 4 beeps - OSDP Address 3

BDC-OSDPBAUD

Use the BDC-OSDPBAUD card to set the OSDP baud rate to configure communication with OSDP Panel. Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 1 beep - 9600 baud
  • 2 beeps - 19200 baud
  • 3 beeps - 38400 baud
  • 4 beeps - 115200 baud

BDC-OUTPUT

Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 3 beeps - Standard Wiegand

Use this option when you want to switch the reader in BDC-TREADER configuration to a BDC-CSN configuration and change the wiring to D0/D1.

BDC-BLUETOOTH

Use the BDC-BLUETOOTH card to switch the Bluetooth radio on and off. Each time this card is presented, the reader indicates the current configuration using a number of short tones:

  • 1 beep - Bluetooth radio disabled
  • 2 beeps - Bluetooth radio enabled

Note

To disable Bluetooth, firmware DEV38 or later is required.

BDC-TREADER

The BDC-TREADER configuration card is used to emulate a "T-Reader" or "Transition Series" reader where it will enable reader with a 2-State Supervised F/2F output and enable the reader to read the card serial numbers for high frequency smart cards.

BDC-WALLET

The BDC-WALLET comes complete with all configuration cards.

© Honeywell International Inc. All Rights Reserved.